| 1. Scope |
| Applicable Connector | 0.5mm Pitch FPC/FFC Connectors (Series Locking) | 16-PIN Top/16-PIN |
| 3. Ratings |
| Rated Voltage (MAX) | AC/DC (Virtual value) 50Hz | 50V |
| Rated Current (MAX) | | 0.4A |
| Ambient Temperature Range | | -25+85 |
| 4. Performance |
| 4.1 Electrical Performance |
| Contact Resistance | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. | 20 m MAX |
| Insulation Resistance | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. | 500M MIN |
| Dielectric Strength | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1 minute between adjacent terminal or ground. | No Breakdown |
| 4.2 Mechanical Performance |
| Locking and Withdrawal Force | Insert and extract applicable FFC at the speed rate of 253mm/minute. (for 0.3mm thick FFC) | Locking: 1.96*n (N) MAX
Withdrawal: 0.49*n (N) MIN |
| Terminal/Housing Retention Force | Pull the terminal at the speed rate of 253mm per minute. | 3.92N MIN |
| 4.3 Environmental and Other Performance |
| Repeated Insertion and Withdrawal | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute. | Contact Resistance: 60 m MAX |
| Temperature Rise | Carrying rated current load. (UL 498) | 30 MAX |
| Vibration | DC 1mA in energized state; Amplitude: 1.5mm P-P; Sweep time: 10-55-10Hz in 1 minute; Duration: 2 hours in each X, Y, Z axes. | Appearance: No Damage
Contact Resistance: 60 m MAX
Discontinuity: 1 ms MAX |
| Shock | DC 1mA in energized state; 490m/s {50G}, 3 strokes in each X, Y, Z axes. | Appearance: No Damage
Discontinuity: 1 ms MAX |
| Heat Resistance | 852, 96 hours; then return to room temperature for 1-2 hours. | Appearance: No Damage
Contact Resistance: 60 m MAX |
| Cold Resistance | -402, 96 hours; then return to room temperature for 1-2 hours. | Appearance: No Damage
Contact Resistance: 60 m MAX |
| Humidity | Temperature: 402; Relative Humidity: 90-95%; Duration: 96 Hours; then measure within 0.5 hours at room temperature. | Appearance: No Damage
Contact Resistance: 60 m MAX
Dielectric Strength: Must meet 4.1.3
Insulation Resistance: 20 M MIN |
| Temperature Cycling | 5 cycles of: a) -553 30 minutes; b) 852 30 minutes. | Appearance: No Damage
Contact Resistance: 60 m MAX |
| Salt Spray | 484 hours exposure to a salt spray from 51% solution at 352. | Appearance: No Damage, Corrosion
Contact Resistance: 60 m MAX |
| SO2 Gas Resistance | 24 hours exposure to 505ppm SO2 gas at 402. | Contact Resistance: 60 m MAX |
| NH3 Gas Resistance | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | Appearance: No Damage
Contact Resistance: 60 m MAX |
| Solderability | Soldering Time: 20.5 sec.
Soldering Temperature: 2355
0.2 mm from terminal tip | Solder Wetting: 95% coverage area |
| Resistance to Soldering Heat | Soldering Time: 50.5 sec.
Soldering Temperature: 2605
0.2 mm from terminal tip | Appearance: No Damage, Deformation |
