| Product Name and Part Number |
| Product Name | FFC/FPC Flat Cable Connector | |
| Part Number | AFC07-S**ECC-00 (Small batch tube packaging) | AFC07-S**ECA-00 (Bulk recommended reel packaging) |
| Ratings |
| Rated Voltage (MAX) | 50V |
| Rated Current (MAX) | 0.5A [AC/DC (Virtual value) 50Hz] |
| Ambient Temperature Range | -45 +85 |
| Electrical Performance |
| Contact Resistance | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. | 20 m MAX |
| Insulation Resistance | Mate applicable FPC/FFC and apply 500V DC between adjacent terminals or ground. | 500M MIN |
| Dielectric Strength | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1 minute between adjacent terminals or ground. | No Breakdown |
| Mechanical Performance |
| Locking and Withdrawal Force | Insert and extract applicable FFC at the speed rate of 253mm/minute. (for 0.3mm thick FFC) | Locking: 1.96*n (N) MAX
Withdrawal: 0.49*n (N) MIN |
| Terminal/Housing Retention Force | Pull the terminal at the speed rate of 253mm per minute. | 3.92N MIN |
| Environmental Performance and Others |
| Repeated Insertion and Withdrawal | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute. | Contact Resistance: 60 m MAX |
| Temperature Rise | Carrying rated current load. (UL 498) | Temperature Rise: 30 MAX |
| Vibration | DC 1mA energized state; vibration along XYZ three directions; amplitude 1.5mm; frequency 10-55-10Hz/min; duration 2 hours. | Discontinuity: 1 ms MAX.
Appearance: No Damage |
| Shock | DC 1mA energized state; along 6 mutually perpendicular directions; impact at 490m/s{50G}; 3 times each. | Discontinuity: 1 ms MAX.
Appearance: No Damage |
| Heat Resistance | Mate applicable FPC/FFC; placed in 852 air for 96 hours; then returned to room temperature for 1-2 hours. | Contact Resistance: 60 m MAX
Appearance: No Damage |
| Cold Resistance | Mate applicable FPC/FFC; placed in -402 air for 96 hours; then returned to room temperature for 1-2 hours. | Contact Resistance: 60 m MAX
Appearance: No Damage |
| Humidity | Mate applicable FPC/FFC; placed in 402, 90-95% relative humidity air for 96 hours; measured within 0.5 hours after returning to room temperature. | Insulation Resistance: 20 M MIN
Appearance: No Damage |
| Temperature Cycling | Mate applicable FPC/FFC; 30 minutes at -452; 10-15 minutes at normal temperature and humidity; 30 minutes at 852; 10-15 minutes at normal temperature and humidity; cycled 5 times. | Contact Resistance: 60 m MAX
Appearance: No Damage, Corrosion |
| Salt Spray | Mate applicable FPC/FFC; 48 hours exposure to 51% salt spray at 352; washed with room temperature water after test; then dried at room temperature. | Contact Resistance: 60 m MAX
Appearance: No Damage |
| SO2 Gas Resistance | Mate applicable FPC/FFC; 24 hours exposure to 505ppm SO2 gas at 402. | Contact Resistance: 60 m MAX
Appearance: No Damage |
| NH3 Gas Resistance | Mate applicable FPC/FFC; 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. | Contact Resistance: 60 m MAX
Appearance: No Damage |
| Solderability | Terminal tip immersed 0.2mm from the reference plane into a tin bath at 2355 for 20.5 sec. | Solder Wetting: 95% coverage |
| Resistance to Soldering Heat | Terminal tip immersed 0.2mm from the reference plane into a tin bath at 2605 for 50.5 sec. | Appearance: No Damage, Deformation |
