| Electrical Performance |
| Contact Resistance | 20 m MAX | Mate applicable FPC/FFC and measure by dry circuit, 20mV MAX, 10mA. |
| Insulation Resistance | 500 M MIN | Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground. |
| Dielectric Strength | No Breakdown | Mate applicable FPC/FFC and apply 200V AC (virtual value) for 1 minute between adjacent terminal or ground. |
| Mechanical Performance |
| Locking Force | 1.96*n (N) MAX | Insert and extract applicable FFC at the speed rate of 253mm/minute. (n=number of positions) |
| Withdrawal Force | 0.49*n (N) MIN | Insert and extract applicable FFC at the speed rate of 253mm/minute. (n=number of positions) |
| Terminal/Housing Retention Force | 3.92N MIN | Pull the terminal at the speed rate of 25 3mm per minute. |
| Environmental Performance |
| Repeated Insertion and Withdrawal | Contact Resistance: 60 m MAX | Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute. |
| Temperature Rise | 30 MAX | Carrying rated current load. (UL 498) |
| Vibration | Contact Resistance: 60 m MAX; Discontinuity: 1 ms MAX; Appearance: No Damage | DC 1mA under energized state; Vibration along XYZ axes, Amplitude: 1.5mm P-P, Sweep time: 10-55-10Hz/min, Duration: 2 hours in each X.Y.Z. axes. |
| Shock | Discontinuity: 1 ms MAX; Appearance: No Damage | DC 1mA under energized state; 490m/s {50G}, 3 strokes in each X.Y.Z. axes. |
| Heat Resistance | Contact Resistance: 60 m MAX; Appearance: No Damage | Mate applicable FPC/FFC; Place in 852 air for 96 hours; then return to room temperature for 1-2 hours. |
| Cold Resistance | Contact Resistance: 60 m MAX; Appearance: No Damage | Mate applicable FPC/FFC; Place in -402 air for 96 hours; then return to room temperature for 1-2 hours. |
| Humidity | Insulation Resistance: 20 M MIN; Contact Resistance: 60 m MAX; Appearance: No Damage | Mate applicable FPC/FFC; Place in 402, 90-95% RH for 96 hours; then measure within 0.5 hours after returning to room temperature. |
| Temperature Cycling | Contact Resistance: 60 m MAX; Appearance: No Damage, Corrosion | 5 cycles of: a) -452 for 30 minutes; b) 852 for 30 minutes; Intermediate condition: Room temperature and humidity for 10-15 minutes. |
| Salt Spray | Contact Resistance: 60 m MAX; Appearance: No Damage | 484 hours exposure to a salt spray from a 51% solution at 352. After test, wash with room temperature water and dry. |
| SO2 Gas Resistance | Contact Resistance: 60 m MAX; Appearance: No Damage | 24 hours exposure to 505ppm SO2 gas at 402. |
| NH3 Gas Resistance | Contact Resistance: 60 m MAX | 40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. |
| Solder Ability | Solder Wetting: 95% coverage | Soldering Time: 20.5 sec. Soldering Temperature: 2355, 0.2 mm from terminal tip. |
| Resistance to Soldering Heat | Appearance: No Damage, Deformation | Soldering Time: 50.5 sec. Soldering Temperature: 2605, 0.2 mm from terminal tip. |
| Ratings |
| Rated Voltage (MAX) | 50V | |
| Rated Current (MAX) | 0.5A [AC/DC (virtual value) 50Hz] | |
| Ambient Temperature Range | -45 +85 | |
