| PRACTICAL TEMPERATURE RANGE RATING | Operating Temperature Range | -25~85C | |
| STANDARD ATMOSPHERIC CONDITIONS | Temperature | 5 TO 35 | |
| Humidity | 45% TO 85% | |
| Pressure | 86Kpa TO 106Kpa | |
| MECHANICAL | Connection Force | After connecting and disconnecting using standard plug gauge 3 times. | MIN 2.0 Kgf (Approx. 19.6N) |
| Disconnecti on Force | After connecting and disconnecting using standard plug gauge 3 times. | MAX 3.75Kgf (Approx. 36.8N) |
| Terminal Strength | A static load of 0.1N/m (1kgf/cm) shall be applied to the tip of the terminal for 1 min in any direction. | No damage to terminal (cracks, looseness, play); electrical and mechanical characteristics shall be satisfied. |
| ELECTRICAL | Contact Resistance | Measured at small current (100mA or less) 1000Hz | 30m MAX |
| Insulation Resistance | Apply a voltage of 100V DC for 1 min to specified portions. | 1000M MIN |
| Dielectric Strength | AC 500V rms (50~60Hz) for 1 min, trip current: 0.5mA. Tested between specified portions. | No damage, arcing, or breakdown etc. |
| DURABILITY | Solderability Test | Terminals dipped 1mm in solder bath of 2305 for 30.5 seconds. | Solder wetting time 3 seconds; Soldering area > 75%. |
| Resistance to Soldering Heat Test | Reflow soldering conditions: Preheat to 180 (120s), Peak temp 2305 (5s). OR Soldering iron method: Bit temp 3305, application time 30.5 sec. | No deformation of case or excessive looseness of terminals; electrical characteristics shall be satisfied. |
| Humidity Test | Stored at 402 and 90% to 96% humidity for 96 Hr, then maintained at standard atmospheric condition for 1 Hr. | Procedures performed after recovery. |
| Heat Test | Stored at 702 for 96 hours, then subjected to controlled recovery at room temperature for 1 hour. | No damage on appearance; Mechanical and electrical characteristics shall be satisfied. |
| Cold Test | Stored at -253 for 96 hours, then subjected to controlled recovery at room temperature for 1 hour. | No damage on appearance; Mechanical and electrical characteristics shall be satisfied. |
| Life Test (Without Load) | Connection and disconnection for 5000 cycles at a speed of 10 to 25 cycles/min. | Contact Resistance 0.1; Disconnection Force 0.8 to 2.0N; Mechanical and electrical characteristics shall be satisfied. |
| Life Test (With Load) | Connection and disconnection for 5000 cycles at a speed of 10 to 20 cycles/min at rating condition (non-inductive load). | Contact Resistance 0.1; Disconnection Force 0.8 to 2.0N; Mechanical and electrical characteristics shall be satisfied. |
| Temperature Cycling Test | Subjected to 5 cycles of specified temperature conditions (e.g., 70 for 0.5hr, -20 for 0.5hr), then returned to room ambient for 30 minutes. | No deformation or cracks in molded part. Insertion & Extraction Force: 3 to 20N. Contact Resistance: MAX.30M. Insulation Resistance: MIN.100 M. Dielectric Withstanding Voltage: 100VAC/min (between terminals). |
| Cold & Heat Shock Test | Subjected to 5 cycles of specified temperature conditions (e.g., 70 for 1hr, -20 for 1hr), then returned to room ambient for 30 minutes. | No deformation or cracks in molded part. Insertion & Extraction Force: 3 to 25N. Contact Resistance: MAX.30M. Insulation Resistance: MIN.100 M. Dielectric Withstanding Voltage: 500VAC/min (between terminals). |
